These are optional Light Blue Kyosho Inferno
Big Bore shock springs, this is the Medium length
and are used on the rear of the MP10 and MP9 as well as the front of the
MP777 STRR truggy. These are considered a medium spring rate.
Here is a spring rate chart of the available
springs for the Kyosho Inferno Big Bores:
These are some guidelines for choosing different spring rates
for your setup on your Kyosho Inferno. Remember that every change you make to
your setup will effect something else. It is a good idea to experiment by
changing settings to get a feel for how changes effect your car with your
driving style. Further reading on the subject of chassis set will also help. Try
and hang with experienced drivers at the tracks you race at will also help
immensely!
You can use different spring rate
shock springs to alter your setup. Basically these are the direct effects of
changing springs:
Effects of Softer Springs:
Gives you more chassis roll
More traction overall
Handles better on bumpy tracks
Shock Bottom out more easily from big jumps |
Effects of Harder Spring:
Less Chassis roll;
Less overall traction
More sharp and responsive
Handles better on smooth tracks
Reduces bottoming from large jumps |
Text Version of the above Chart:
| Short Length Shocks
(S) 70mm |
Medium Length Shocks (M) 84mm |
Long Length Shocks (L) 95-97mm |
| Softer |
Softer |
Softer |
Green IF350-814 - 8 turns 1.4
wire
Orange IF-350-7514 - 7.5 turns 1.4 wire
Light Blue IF350-714 - 7 turns 1.4 wire
White IF350-1016
- 10 turns 1.6 wire
Gray IF350-6514 - 6 turns 1.4 wire
Purple IF350-916 - 9 turns 1.6 wire
Light Green IF350-816 - 8 turns 1.6 wire
Blue IF350-716 - 7 turns 1.6 wire |
Yellow
IS106-9514 - 9.5 turns 1.4 wire
Green IS106-914 - 9 turns 1.4 wire
Orange IS106-8514 - 8.5 turns 1.4 wire
Light Blue IS106-814 - 8 turns 1.4 wire
White
IS106-1116 - 11 turns 1.6 wire
Purple IS106-1016 - 10 turns 1.6 wire
Light Green IS106-916 - 9 turns 1.6 wire
Blue IS106-816 - 8 turns 1.6 wire |
Green
IF348-1114 - 11 turns 1.4 wire
Light Blue IF348-1014 - 10 turns 1.4 wire
White IF348-1316 - 13 turns 1.6 wire
Purple IF348-1216 - 12 turns 1.6 wire
Light Green IF348-1116 - 11 turns 1.6 wire
Blue IF349-1016 - 10 turns 1.6 wire
Red IF348-916 - 9 turns 1.6 wire
|
| Harder |
Harder |
Harder |
Explanation for the
spring rates in the charts above:
The part number of the Kyosho spring has the wire thickness
and number of turns included in it.
For example:
IF350-716 equates to:
7 turns of 1.6 thick wire.
This can be extrapolated to all the springs and you will see
the pattern evolve for the spring rates.
Thicker wire = stiffer spring
More turns in wire = softer spring
Just think of this like a spring is a piece of wire. If you
straightened out the wire and held it on one end, the longer it is, the easier
it would bend by pushing on it from the opposite end. The same would hold true
for a thinner piece of wire, it would be easier to bend as well. This is how
springs are actually working. The longer the wire the easier it is to bend and
therefore the softer spring rate it has. An advantage of lower turns and thinner
wire is you can create a spring with lighter weight vs. a spring with thicker
wire and more turns. Keep this in mind when choosing springs to run as well.
I hope this explanation helps rid some confusion about how
the above charts work.
